Supercritical CO2 Extraction – Completely Silent – No Air Compressor Required – Start Your Botanical Oil Extraction Profits Today – Fast 1-4 Hour Extraction. Great for terpene extraction and full spectrum hemp oil right out of the machine. Produces the best quality hemp extract in the industry. Leave waxes behind if you run near subcritical (reduces or eliminates winterization). Output oil straight out of the machine near CB D isolate quality (85 percent CB D’s )
Live Resin Cannabis Processing and Diamond Mining: Using a live resin process, this system can be used for processing the basis of recrystallization (Diamond Mining or Jar Tech). The separation of CB D from terpenes is what Diamond Mining (crystallization of terp sauce) is all about, and is incredibly flavorful and potent end product.
Price: $99,000 + chiller + training + freight = $111,000 Systems in inventory.
High Quality Full Spectrum Oil – Right Out of the Machine: Run this system at lower pressure and get a very high quality crude oil output (little to no winterization needed), which is 80 percent CB D (very near isolate quality) which you can bottle and sell to the consumer directly.
Supercritical CO2 Extracted Hemp Oil commands a buy price of almost twice that of ethanol or other conventional extracted methods. Using the Infinity Supercritical CO2 extractor with hemp is considered a full spectrum oil extraction.
We see wholesale buy prices for CO2 extracted hemp oil at $6.0/gram to $10.00+/gram in Wisconsin. On a retail level, one gram of CO2 extracted full spectrum hemp oil, which is combined with 1 oz of carrier oil (coconut oil) sells for $45.00+ at retail stores. Your cost of production, including the bottle, hemp flower, and processing is typically less than $3.00 If you sell your brand, on your own website, then you can see those higher retail prices, and profits.
What’s Wrong With Ethanol Extraction ?
The Problem With Large Scale Ethanol Batch Extraction: Typically, large scale ethanol extraction has a number of drawbacks. Since recycled ethanol is imperitive to low cost processing operation, the dilution of the pure ethanol becomes compromised (water keeps getting added) which results in poor extraction efficiency. In addition, ethanol has poor turpene retention (turpepes become volatile and simply evaporate). Finally, many ethanol processors who do a quick-turn extraction, end up with lots of bitter green tasting chlorophyll. To filter out that, they use activated carbon filters (referred to as carbon scrubbing), which also filter out most of the valuable components ( source: Romano LL, Hazekamp A. Cannabis Oil: chemical evaluation of an upcoming cannabis-based medicine. Cannabinoids. 2013;7(1):1-11.)
Supercritical CO2 Extraction Produces The Best Quality Full Spectrum Hemp Oil
Silent Running and Saves Time and Your Money: No more loud air compressors. No more waiting 12-24 hours for your batch processor to complete its cycle. Your time is money. Use your time to make extracts faster. This system will result in less time spent with maintenance, or waiting for a long extraction process, and will provide you with more time that is spent extracting profit from Cannabis. This system provides a faster extraction and cuts your cycle time to extract more oil in less time. Silent operation.
Infinity Supercritical now has its own laser, and engraves parts to take the user experience to the next level. We meticulously laser cut our caster beam frame, then sandblast it, and powercoat the frames for a professional finish (a final clear coat is applied for longevity).
Product: The 10L is a batch fed botanicals crude oil extractor, using supercritical CO2 technology, which is well proven in the food processing (coffee decaf) and pharmaceuticals industry.
Profits: The 10L allows processing of small amounts (number up machines for medium amounts) of botanicals extraction, compared to other batch reactors. Using our FlowBar, production is reduced down to 1-4 hours per cycle. This allows better processing efficiency, which saves labor and energy costs, and increases your profit potential.
Time: The 10L saves you time. The FlowBar methodology gets you finished product faster, and at less production cost.
Low Carry-Over (More Extracted Oil You Can Sell): Reducing carry-over saves time and parts costs in system maintenance, and puts more profit into your pocket. It also means less time spent on upkeep with the machine, and more time spent on extracting oil.
Target Oil and Reduce Post Processing Time (Save more than 50 percent of your time by targeting oil you want, not wax): Systems are designed to target oil production at pressures lower than 2,000 psi, which specifically can retain valuable terpenes, and emphasize oil harvesting, instead of waxes and other byproducts, which need to be removed in post processing. The crude oil output from the 10L is considered a full spectrum hemp oil, and can be sold directly as-is, or mixed with a carrier oil (such as coconut oil) and bottled for sale.
Run 2 Months Without Pump Cleaning: Quiet, reliable, and lowest maintenance CO2 pump in the industry. We have one customer who has run his machine almost everyday for 2 months without cleaning his CO2 pump. We also are the first company to provide a bolt-on pump cleaner to clean your pump head in-place. We specialize in collecting the oil before it gets to the CO2 pump using our proprietary electrostatic collector. Others make you buy additional pumps, or require cleaning every few days.
Cleaning: Respect your equipment, and it will operate great. We recently had one customer comment that the 10L was a “gold mine” and was looking forward to his second machine, to make even more profit. Keeping a system clean so that it operates correctly is true with most equipment. We recommend always keeping your machine clean, and at least every 15 cycles do a thorough ethanol clean out of the system. If you do not clean your machine, expect that it will not work at all. We’ve had customers that don’t clean their machine at all, and they go through seals on a weekly basis, then wonder why it isn’t operating up to expectations. We’ve had a few groups return machines for repair, and all that was needed was a good machine cleaning. Have some respect for your profit center, and you’ll get great results.
System Components: 3 collection vessels with bottom exit valves, heat recovery system, CO2 preheat, electrostatic collection, FlowBar, spares package, shipping, crate, chiller, extra baskets, bolt on pump cleaner, training, support, pump head cleaning holder, vent tube and manifold, CO2 monitor, CO2 liquid sight-glass.
CO2 Extraction System Full Configuration:
Capacity: 10 Liter (2-3 pounds of hemp flower)
Operation: Semi-Automatic Pressure: 2,000 psi
Power: 220V 60hz Single Phase (for European installations you must have 60hz)
Engineer Peer Reviewed: California, Colorado, Nevada, Washington, Oregon, Arizona
Modular Fluid Extractor 10L – Run SubCritical or Supercritical CO2
System holds about 10 Liters volume of botanicals (inside extraction vessel is about 48 x 4 inches or 600 cubic inches or almost 10 L). We do not recommend finely ground material that cannot be contained within the 40 micron botanicals basket.
How it Works: High pressure liquid CO2 is pumped into a extraction vessel, which brings the CO2 supercritical as it goes into the separation/collection vessels. As the botanicals come in contact with the CO2, the oil is released into the CO2, since the CO2 acts as a solvent. The gas and oil (co-mingled) are released into the separation/collection vessel where the pressure drops and the botanical oil drops out as a liquid. The CO2 gas is then condensed back to a liquid via a small heat exchanger, and then recirculated through a CO2 pump to start the cycle over.
Electrostatic Precipitator: Infinity Supercritical is the first in the industry to utilize static electricity to assist in collection of oil. Commonly known as ESP, electrostatic precipitation is a method used in many industries to remove particulates in a gas flow. In this case, we’re applying some same technology (but with our own invention) to collect Cannabis oil. A small charge accumulates in the entrained oil, which makes it adhere to the first collection vessel.
Semi-Automated: Turn the CO2 pump on, and leave it on. You can adust the pump speed, which sets the pressure. The system runs in a steady-state once started. This is a 2,000 psi or less working pressure system. Typical runs will be at 1,300 to 1,800 psi. The system working pressure is rated for 2,000 psi. A safety relief vavle is provided to release any pressure which goes above 2,000 psi. Targets oil at or below 2,000 psi to minimize post processing. High Pressure Systems (above 2000 psi) = lots of post processing.
Fittings: We use quality Swagelok fittings. System is made in the USA.
Pump Cleaner: Use our optional pump cleaner to clean the pump without removing the pump head.
FlowBar: The CO2 FlowBar enhances the CO2 delivery and distribution within the botanicals extraction vessel. While almost every CO2 extraction system enters in one end and exits the other, our new concept delivers CO2 in a uniform manner throughout the entire extraction vessel. The result is a much faster, and more thorough extraction.
Instructional Videos for Start-up, Training, Operation, and Maintenance
NEW CO2 HEMP EXTRACTION SUPPORT EQUIPMENT
Infinity Supercritical 10L CO2 Extraction Support and Operations Cart
Time to Build: 2 weeks (depending on order queue)
Buy via PayPal:
Collection Vessel Holder | COLLECTION-VESSEL-HOLDER | Collection Vessel Holder for CO2 system. | Shipping included in price | Price: $600.00
Learn Extraction Properly
Recommended Learning Schedule and Strategy: After selling lots of systems, and determining the best practice to learn extraction, we have developed a learning system to help you minimize pump maintenance, and maximize yield and successful extraction runs. If you follow our learning plan, and practice extraction runs on hops, you can expect proper system operation, low pump maintenance, and extractions up to the full oil content of your botanicals. 100 percent of operator problems at first start-up are due to the operator forgetting training. We suggest you run your machine a week after training.
If you follow this schedule, you will learn quickly. If you do not follow this schedule, then you can expect pump clogging, building pressure issues, and lack of yield or extract. If you decide to not follow our plan, then you can expect to have pump problems (from improperly running the system) and little to no yield (extraction). To be clear, if you do not follow our recommended plan, you may get zero results. Prior experience on other CO2 extraction machines doesn’t make any difference to running a new machine, with a different configuration. To be clear, you need proper training, and follow a well thought-out plan to succeed if you want to have great extractions.
Learning Methodology Schedule For Extraction
We suggest you do several practice runs with the machine empty (no botanicals – just CO2) and then practicing using hops (with known oil content). We recommend using 1 pound of hops in the extraction vessel, and doing at least 10 practice runs up to 1,400 psi. Adjust the extraction time from 1 to 4 hours, and see how your results may vary. You may also practice with doing the first 30-45 minutes without any heat, to collect terpenes. Practice on low value hops first, gain experience, then move on to your trim or bud.
Improper use of the 10L system can result in component damage, which is not a warranty issue, it’s a flag for the operator to continue to learn, and train with the system for proper, profitable operation. Unless you have had your botanicals tested for oil content, we do not recommend learning on any botanicals with unknown oil content. To be clear, do not use your trim or bud to start with.
Buyer beware. You have no idea if your machine runs, if you purchase from Ebay, or used, unless it has been certified/reconditioned and tested by Infinity. We do not provide support for used machines, unless you have done reconditioned/certification at our shop. Support is not included with your used machine. Any recertification, parts, support, or any time, is extra, and billed on a customer and per-case basis. If your machine does not run, we may not support it at all (since we have no idea if it has been damaged, modified, etc.). There is no warranty for used machines.
Purchasing Used Machines: Any used machine may or may not be operational. It is your responsibility to determine the operability of the machine prior to purchase, or just assume it does not work at all. Please purchase a new machine with a warranty. All service, support, and parts are additional, and on a per-quote basis. All service and support is on a “best-efforts” basis.
If you have a question regarding a used machine purchase, please call us at the number at the top of the page, or please email: firstname.lastname@example.org